|
Post by pumpkinracing on Mar 18, 2020 20:02:26 GMT -5
Got 20mcs on line a bit rough but a start just received . Took some pictures of the start no spark compression 75 psi looks like it’s going to be a complete rebuild . Any help with parts locating would be helpful.cleaned degrease today cleaned bar and chain. link
|
|
|
20mcs
Mar 19, 2020 8:29:32 GMT -5
Post by sweepleader on Mar 19, 2020 8:29:32 GMT -5
Looks complete, that is half the battle. Well, a couple things missing.
Post what you need, someone will be able to help.
|
|
|
20mcs
Mar 19, 2020 19:16:11 GMT -5
Post by riseandrun on Mar 19, 2020 19:16:11 GMT -5
Nice pictures. NICE workshop! :-) I can't believe that chain on the bar is the same chain laying in a rusty pile on your cart! Looking forward (like all the rebuilds) to seeing it up and running.
|
|
|
20mcs
Mar 20, 2020 18:36:30 GMT -5
Post by pumpkinracing on Mar 20, 2020 18:36:30 GMT -5
It’s amazing what pb penetrating oil and a wire wheel can do it did take me two hours with a vise grip plus channel locks to get everything free.
|
|
|
Post by pumpkinracing on Mar 21, 2020 16:22:04 GMT -5
With all this corona virus been doing a lot of work on saws . Got 20 mcs almost apart need to pull flywheel. Is there any thing special to do this or just grab that puller and go to town. Got side tracked when short block for the trash pump came and I started taking that apart . So far the jug, piston ,rings are the same trying to find what else I can use. Started glass beading parts .heres some pictures for the update. Anthony imgur.com/a/YFX3pQQ
|
|
|
20mcs
Mar 26, 2020 23:12:56 GMT -5
Post by onlyhomelites on Mar 26, 2020 23:12:56 GMT -5
Damn nice progress there! Nicely done!
|
|
|
Post by sawnami on Mar 29, 2020 7:57:23 GMT -5
I recently finished a crankshaft up restoration on one. I'd be glad to help if you have any questions. I may be trading my other one off today.
|
|
|
20mcs
Mar 31, 2020 19:01:09 GMT -5
Post by pumpkinracing on Mar 31, 2020 19:01:09 GMT -5
Been making good progress, still need a fuel tank and a handle bar and an air filter bracket that the rotating handle goes in. Haven’t split the crank case yet, was wondering if I really need to if I do a leak down test, how often does the intake plate wear out. I have glass beaded painted and started putting together some things already. Here are some pictures for an update: imgur.com/a/IYYZyBL
|
|
|
Post by onlyhomelites on Mar 31, 2020 22:53:24 GMT -5
Very nice! You might just inspire me to clean the crap away from the blast cabinet and get a few of my projects going again!
|
|
|
Post by sawnami on Apr 3, 2020 21:53:24 GMT -5
Been making good progress, still need a fuel tank and a handle bar and an air filter bracket that the rotating handle goes in. Haven’t split the crank case yet, was wondering if I really need to if I do a leak down test, how often does the intake plate wear out. I have glass beaded painted and started putting together some things already. Here are some pictures for an update: imgur.com/a/IYYZyBLWhen I took mine apart, I lapped the sealing face of the valve and the formica wear plate It depends on the use that the saw has seen.
|
|